2.How to update clone Opcom firmware to 1.59
3.opcom user manual
4.using opcom to program key
5.Anyne got the Opcom usb drivers?
6.opcom - what can be done?
China Clone OPCom 2015 Firmware 1.59 CAN OBD2 Diagnostic Tool for Opel with PIC18F458 Chip:
eobdtool
Welcome to eobdtool.co.uk
2015年9月8日星期二
All about opcom China clone firmware 1.59
1.opcom china clone install (OP-COM opcom 2010V firmware 1.59 installation step-by-step)
2.How to update clone Opcom firmware to 1.59
3.opcom user manual
4.using opcom to program key
5.Anyne got the Opcom usb drivers?
6.opcom - what can be done?
China Clone OPCom 2015 Firmware 1.59 CAN OBD2 Diagnostic Tool for Opel with PIC18F458 Chip:
2.How to update clone Opcom firmware to 1.59
3.opcom user manual
4.using opcom to program key
5.Anyne got the Opcom usb drivers?
6.opcom - what can be done?
China Clone OPCom 2015 Firmware 1.59 CAN OBD2 Diagnostic Tool for Opel with PIC18F458 Chip:
How to program Astra key with OPCOM 2012V
Before using OP COM China Clone to make key for your Astra, 4 things you need to know in advance.
1. NEW remote central locking board (PCB) to the car
2. A key to the car
3. The Security Pass for the car
4. Opcom OP-Com 2012V with Firmware V1.59
OPCOM
How to install Opcom firmware 1.59 (the following video link is offered for your reference)
http://opcom-china-clone.blogspot.com/2015/09/op-com-opcom-2010v-firmware-159.html
And then the following part is the operation guide:
Step1. Insert your NEW remote central locking board into your key;
Step2. Put the key into the ignition and turn but Do Not crank the engine;
Step3. Connect OPCOM with your car and your computer (that has already finished software installation);
Step4. Open OPCOM software and click on “DIAGNOSTICS” (mark red at picture below);
OPCOM-1
Step5. A vehicle identification menu will pop out in the next page. Select your car year;
Step6. And then select your car model;
Step7. Select “BODY” from the menu.
OPCOM-2
Step8. Select “ANTI THEFT WARNING”;
Step9. Press “PROGRAMMING” button (locate on the right hand side of the screen);
Step10. Select “SECURITY CODE” (this should be the only one available at the time).
Step11. Enter your “SECURITY CODE” and click OK.
Step12. Select “PROGRAMMING REMOTE CAR KEY”;
Step13. Follow the on screen instructions.
Step14. Click “CLOSE”.
Step15. Open and close door, try locking your door and then dead lock it. Once you have done this, unlock and all should be done.
1. NEW remote central locking board (PCB) to the car
2. A key to the car
3. The Security Pass for the car
4. Opcom OP-Com 2012V with Firmware V1.59
OPCOM
How to install Opcom firmware 1.59 (the following video link is offered for your reference)
http://opcom-china-clone.blogspot.com/2015/09/op-com-opcom-2010v-firmware-159.html
And then the following part is the operation guide:
Step1. Insert your NEW remote central locking board into your key;
Step2. Put the key into the ignition and turn but Do Not crank the engine;
Step3. Connect OPCOM with your car and your computer (that has already finished software installation);
Step4. Open OPCOM software and click on “DIAGNOSTICS” (mark red at picture below);
OPCOM-1
Step5. A vehicle identification menu will pop out in the next page. Select your car year;
Step6. And then select your car model;
Step7. Select “BODY” from the menu.
OPCOM-2
Step8. Select “ANTI THEFT WARNING”;
Step9. Press “PROGRAMMING” button (locate on the right hand side of the screen);
Step10. Select “SECURITY CODE” (this should be the only one available at the time).
Step11. Enter your “SECURITY CODE” and click OK.
Step12. Select “PROGRAMMING REMOTE CAR KEY”;
Step13. Follow the on screen instructions.
Step14. Click “CLOSE”.
Step15. Open and close door, try locking your door and then dead lock it. Once you have done this, unlock and all should be done.
opcom user manual
OP Com China Clone CAN OBD2 Diagnostic Tool for Opel with PIC18F458 Chip:
 | Opcom Immobiliser Guide.pdf Size : 0.49 Type : pdf2 Kb |
| Opcom Airbag Coding.pdf Size : 0.085 Kb Type : pdf |
| Opcom SDM Programming.pdf Size : 0.014 Kb Type : pdf |
| Opcom Diesel Pump Programming.pdf Size : 0.013 Kb Type : pdf |
| Opcom Manual DPF Regeneration.pdf Size : 0.208 Kb Type : pdf |
| Opcom Injector Programming.pdf Size : 0.329 Kb Type : pdf |
| Opcom New CIM Programming.pdf Size : 0.016 Kb Type : pdf |
| Opcom Throttle Body Reset.pdf Size : 0.01 Kb Type : pdf |
| Opcom Clear SDM Deployment Data.pdf Size : 0.01 Kb Type : pdf |
| Opcom Towbar And Trailer Module Coding.pdf Size : 0.013 Kb Type : pdf |
| Opcom Read Security Code.pdf Size : 0.011 Kb Type : pdf |
| Opcom Service Interval Reset.pdf Size : 0.016 Kb Type : pdf |
| DLC Locations.pdf Size : 0.266 Kb Type : pdf |
| Opcom Cruise Control.pdf Size : 0.004 Kb Type : pdf |
| Dis (Display) Code Index List.pdf Size : 0.018 Kb Type : pdf |
| Replace the BCM.pdf Size : 27.825 Kb Type : pdf |
| Easytronic.pdf Size : 569 Kb Type : pdf |
Forced DPF Regeneration
You can start the forced regeneration on the following models:
Astra-H
Z19DT, Z19DTH, Z19DTL, Z17DTR, Z17DTJ
Zafira-B
Z19DT, Z19DTH, Z19DTL, Z17DTR, Z17DTJ
Vectra-C / Signum
Z19DT, Z19DTH, Z19DTL
Corsa-D
Z13DTH, Z17DTR
Antara
2.0L Diesel engine
Warning
The exhaust gas temperature will increase to over 600 °C, so you must perform this outside,
on a non-flammable ground.
The regeneration procedure is completely controlled by the engine control unit.
Prerequisites
Engine is running at idle
Engine is fully warmed up
To avoid consequential damages, the DPF regeneration must be executed only once!
EDC16 System
Note, after "DPF Regeneration" is finished live data "Diesel Particulate Filter
Saturation" will show 70%. When engine controller has performed a dynamic
regeneration value will be changed.
DECE01 System
Astra-H
Z19DT, Z19DTH, Z19DTL, Z17DTR, Z17DTJ
Zafira-B
Z19DT, Z19DTH, Z19DTL, Z17DTR, Z17DTJ
Vectra-C / Signum
Z19DT, Z19DTH, Z19DTL
Corsa-D
Z13DTH, Z17DTR
Antara
2.0L Diesel engine
Warning
The exhaust gas temperature will increase to over 600 °C, so you must perform this outside,
on a non-flammable ground.
The regeneration procedure is completely controlled by the engine control unit.
Prerequisites
Engine is running at idle
Engine is fully warmed up
To avoid consequential damages, the DPF regeneration must be executed only once!
EDC16 System
Note, after "DPF Regeneration" is finished live data "Diesel Particulate Filter
Saturation" will show 70%. When engine controller has performed a dynamic
regeneration value will be changed.
DECE01 System
Diesel Pump Programming - opcom user manual
Donor-car
Remove dieselpump from donor-car
Attention: You will need donor-car's Security Code!
Car where donor-pump needs to be installed
Install dieselpump in the car
Set up communication with ECM
Select [Programming]
Select [Reset ECU]
Enter donor-car's Security Code
This will reset the previously learnt security code. Then, your engine ECU (which is inside the
pump) will be resetted, so you can learn it to the new car.
Set up communication with Immobilizer module
Select [Programming]
Enter Security Code of car where you have installed the dieselpump
Select [Immobilizer Function Programming]
Select [ECM (Motor Module) replaced]
This will learns the new Security Code to the engine control module.
Astra-G and Zafira-A can also be installed with a VP44/PSG5 for Y20DTH. These PSG5 units
don't need to be reset.
Vectra-C / Signum PSG16
Donor-car
Remove the diesel pump from donor-car
Attention: You will need donor-car's Security Code!
Car where donor-pump needs to be installed
Install diesel pump in the car
Set up communication with ECM
Select [Programming] Select [Reset ECU]
Enter donor-car's Security Code
This will reset the previously learnt security code. Then, your engine ECU (which is inside the
pump) will need to be reset, so you can learn it to the new car.
Set up communication with CIM module
Select [Programming]
Enter Security Code of car where you have installed the diesel pump
Select [Immobilizer Function Programming]
Select [ECM (Motor Module) replaced]
This will learns the new Security Code to the engine control module.
Reset immobilizer related controllers
Then, you need to go into each module, for which you have a corresponding fault code stored
in the CIM module (see below), and do a reset/programming cycle with the security code of
the car.
IPC Instrument B3925 -00 Wrong Environment Identifier Received IPC
REC Rear Electrical Centre B3929 -00 Wrong Environment Identifier
Received REC
BCM Body Control Module B3924 -00 Wrong Environment Identifier
Received BCM
DDM Driver Door Module B3926 -00 Wrong Environment Identifier Received
DDM
PDM Passenger Door Module B3927 -00 Wrong Environment Identifier
Received PDM
After the reset, you need to wait at least 10 seconds with the ignition OFF, to allow the car to
learn the new identifier.
Now select ECM and check programming of:
Highspeed CAN bus
Variant configuration
Tyresize
Remove dieselpump from donor-car
Attention: You will need donor-car's Security Code!
Car where donor-pump needs to be installed
Install dieselpump in the car
Set up communication with ECM
Select [Programming]
Select [Reset ECU]
Enter donor-car's Security Code
This will reset the previously learnt security code. Then, your engine ECU (which is inside the
pump) will be resetted, so you can learn it to the new car.
Set up communication with Immobilizer module
Select [Programming]
Enter Security Code of car where you have installed the dieselpump
Select [Immobilizer Function Programming]
Select [ECM (Motor Module) replaced]
This will learns the new Security Code to the engine control module.
Astra-G and Zafira-A can also be installed with a VP44/PSG5 for Y20DTH. These PSG5 units
don't need to be reset.
Vectra-C / Signum PSG16
Donor-car
Remove the diesel pump from donor-car
Attention: You will need donor-car's Security Code!
Car where donor-pump needs to be installed
Install diesel pump in the car
Set up communication with ECM
Select [Programming] Select [Reset ECU]
Enter donor-car's Security Code
This will reset the previously learnt security code. Then, your engine ECU (which is inside the
pump) will need to be reset, so you can learn it to the new car.
Set up communication with CIM module
Select [Programming]
Enter Security Code of car where you have installed the diesel pump
Select [Immobilizer Function Programming]
Select [ECM (Motor Module) replaced]
This will learns the new Security Code to the engine control module.
Reset immobilizer related controllers
Then, you need to go into each module, for which you have a corresponding fault code stored
in the CIM module (see below), and do a reset/programming cycle with the security code of
the car.
IPC Instrument B3925 -00 Wrong Environment Identifier Received IPC
REC Rear Electrical Centre B3929 -00 Wrong Environment Identifier
Received REC
BCM Body Control Module B3924 -00 Wrong Environment Identifier
Received BCM
DDM Driver Door Module B3926 -00 Wrong Environment Identifier Received
DDM
PDM Passenger Door Module B3927 -00 Wrong Environment Identifier
Received PDM
After the reset, you need to wait at least 10 seconds with the ignition OFF, to allow the car to
learn the new identifier.
Now select ECM and check programming of:
Highspeed CAN bus
Variant configuration
Tyresize
How to update clone Opcom firmware to 1.59
This guide will help you how to upgrade clone Opcom firmware to 1.59, As we all know, clone opel Op-com diagnostic interface just work with 2010.08 opcom software, and with 1.45 firmware.
New OPCOM China Clone is available now. Below we make the upgrade instruction of Op com china clone 2014 Opcom firmware upgrade to 1.59 guide.
1: True V1.39 Firmware PCB
New OPCOM China Clone is available now. Below we make the upgrade instruction of Op com china clone 2014 Opcom firmware upgrade to 1.59 guide.
1: True V1.39 Firmware PCB
2: Latest V1.45 Firmware PCB
How to update clone Opcom firmware to 1.59
Step 1: Download free 2014 op-com software, and install the program.
2010.08 opcom clone software Free download link:
Step 2: Make sure obd tools website (obdtool.co.uk) Op com china clone 2014 onnect the computer to install the drivers correctly, PLS disconnect the internet.
Step 3: Open the OCflash and update the op-com with firmware 1.59 HEX file
Step 4: At last we opened the vaux-com software version is 2012.08, you can check obdtool.co.uk opcom firmware version have be updated to 1.59.
OP-COM opcom 2012V firmware 1.59 installation step-by-step
OP COM USB diagnostic interface for Opel and Vauxhall firmware has newly updated to V1.59. Here is the step-by-step instruction on how to install opcom China Clone software.
Software version (SW): 08/2010
Firmware version (FW): V1.59
How to install OP-COM 1.59 software?
1) Install Op-com driver
Open My Computer
Open OP-COM (E:) CD software
Create a new folder “op-com” on Local Disk (C:)
Copy all files in OP-COM CD to the “op-com” folder
Send OP-COM Diagnostic software to Desktop (create shortcut)
Connect China
Wait the system to detect hardware wizard
Select “Install from a list or specific location (Advanced)”, click “Next”
Include and browse location to C:﹨op-com﹨Drivers, click OK
Click “Next”
Click “Next”
Click “Finish” when opcom driver is completely installed
Open My Computer>>Manager>>Device Manager>>Universal Serial Bus controllers>>USB Serial Converter to make sure well communication is built
2) Run Op-com software and diagnose
Plug the op-com cable with vehicle via OBD diagnostic socket
Open “Shortcut to OP-COM” software on desktop
OPCOM CHINA-CLONE 08/2010
Click “Settings”
Click “Test Interface”, you will able to see the OPCOM serial number and firmware version V01.59
Click “Close”
Click “Save Config”
OP-COM Configuration saved! Press “OK”
Back to Opcom software main menu
Select “Diagnostic” function
Select “Automatic Vehicle Identification”
Select “KWP-2000” (K-line) or “CAN” and select diagnostic connector
The op-com 2010V software will display vehicle information, VIN, model, engine code etc
Click “Diagnose ECM” button
Select ECM type and diagnostic connector
Click “Fault Code”
Op-com will display all error codes stored in ECM
The click “Clear Fault Codes” to erase error codes
Perform other diagnostic functions or exit the software program
Unplug the op-com USB interface.
订阅：
博文 (Atom)